Roof flashing is the thin metal or membrane that seals the joints of a roof, where water would otherwise get in: along the edges, in valleys, around chimneys, skylights, vents and walls. The main types of roof flashing are drip edge, step flashing, counter flashing, valley flashing and pipe boots. In Quebec, where snow, ice and freeze-thaw cycles put roofs under stress, worn or badly installed flashing is one of the most common causes of leaks.
This guide explains each type of roof flashing, the materials used, the signs of failure, indicative repair costs as of 2026 and what to check in a roofing quote so flashing is done properly when you repair or replace your roof.
Roof Flashing Types: Why Flashing Matters
Shingles and metal panels shed water well on flat, open surfaces. Problems start where the roof surface is interrupted: an edge, a change in slope, a wall or an object that goes through the roof. At each of these points, water can run sideways or backwards under the roofing material. Flashing guides that water back onto the roof surface and into the gutters.
In the Laurentides, flashing also has to cope with snow that sits for weeks, ice dams at the eaves and meltwater that refreezes overnight. A small gap that would be harmless in a mild climate can let water in every time the snow melts.
The Main Types of Roof Flashing
| Flashing type | Where it goes | What it does | Common problem |
|---|---|---|---|
| Drip edge | Along the eaves and rakes | Directs water into the gutter and protects the deck edge | Missing or installed behind the gutter incorrectly |
| Step flashing | Where a roof meets a side wall or dormer | Overlapping pieces woven with each shingle course | Reused old pieces, gaps at the bottom |
| Counter flashing | On chimneys and walls, over the step flashing | Covers the top of the base flashing | Loose mortar joint or failed sealant |
| Valley flashing | Where two roof slopes meet | Channels a high volume of water | Debris build-up, worn metal, poor overlap |
| Pipe boots and vent flashing | Around plumbing vents and exhaust pipes | Seals the penetration | Cracked rubber collars after years of sun |
| Skylight flashing kits | Around skylights | Manufacturer-designed seal | Improvised kits or sealant-only repairs |
| Kick-out flashing | Bottom of a roof-to-wall joint | Diverts water away from the wall | Missing, causing wall rot or stains |
Drip edge
A drip edge is an L-shaped metal strip installed along the edges of the roof. At the eaves it lets water drip into the gutter instead of curling back onto the fascia, and at the rakes it protects the edge of the roof deck. It is inexpensive and should be part of almost every shingle roof replacement.
Step flashing and counter flashing
Where a sloped roof meets a vertical wall, such as a dormer, a second storey or a chimney, step flashing is installed as a series of small L-shaped pieces, one per shingle course. Counter flashing then covers the top of the step flashing, often set into the mortar of a chimney or tucked behind siding. This two-part system lets the house and roof move without opening a gap.
Valley flashing
Valleys collect water from two slopes, so they see more flow than any other part of the roof. They can be open, with exposed metal, or closed, with shingles woven or cut over a membrane. In both cases, a self-adhered underlayment beneath the valley is an important line of defence in snowy climates.
Pipe boots and vents
Plumbing vents and exhaust pipes pass through the roof with a flashing base and a rubber or metal collar. Rubber collars can crack after many years of sun and cold, a frequent cause of small leaks that show up as stains on a ceiling.
Flashing Materials
- Galvanized or pre-painted steel: widely used, durable and affordable.
- Aluminum: light and rust-resistant, common for drip edges.
- Copper: very long-lasting and attractive, but more expensive.
- Self-adhered membranes: used under flashing and in valleys as a secondary barrier.
- Rubber (EPDM) collars: used on pipe boots; check them during inspections.
Avoid mixing incompatible metals in contact with each other, which can cause corrosion over time. Your roofer should choose materials that work together and with your roofing type.
Signs of Failing Flashing
- Water stains on ceilings near a chimney, skylight or wall.
- Damp or rotting wood around dormers or on the fascia.
- Rust, bent or lifted metal visible from the ground.
- Cracked sealant or mortar around chimney flashing.
- Drips in the attic during heavy rain or snow melt.
- Ice build-up at the base of walls or in valleys in winter.
If you notice any of these signs, have the area inspected before winter, since snow and ice can turn a slow drip into significant damage in a few weeks. Our guide on why your roof is leaking walks through other common causes so you can narrow down the source.
Repair or Replace Flashing?
Small issues, such as resealing a counter flashing joint or replacing a cracked pipe boot, are often handled as repairs. When the roof itself is being replaced, it is usually wise to replace all flashing at the same time, rather than reusing old pieces that may fail before the new shingles. Re-using old step flashing is a common shortcut to watch for in quotes.
As of 2026, indicative costs in the region are roughly in the following ranges, depending on access, roof slope and materials: a simple pipe boot replacement from about $150 to $400, resealing or partly redoing chimney flashing from about $400 to $1,500, and a full chimney or skylight reflashing more. Valley repairs vary widely with length and condition. These figures are only rough guides; get a written quote. For leak repair options, see our page on roof repair and leaks.
Checklist: Flashing Items to Look for in a Roofing Quote
- New drip edge at eaves and rakes.
- New step flashing at every roof-to-wall joint, not reused.
- Counter flashing on chimneys checked, resealed or replaced.
- Valleys with self-adhered membrane and a stated valley method.
- New pipe boots and vent flashing.
- Skylight flashing kit from the manufacturer, or replacement of the skylight if it is old.
- Kick-out flashing where roofs meet walls above siding.
- Materials and colours specified in writing.
- Warranty terms that cover workmanship on flashing.
To understand the full sequence of work, read our step-by-step roof replacement process.
FAQ
What is the most common roof flashing problem?
Leaks around chimneys and at roof-to-wall joints are among the most common, often caused by failed sealant, old step flashing or missing counter flashing.
Is drip edge required?
Requirements can vary, but drip edge is considered good practice on shingle roofs and is included in most quality installations.
Can flashing be reused during a roof replacement?
Some heavy flashing in perfect condition may be reused, but replacing step flashing, pipe boots and drip edge with the new roof is usually recommended.
Can I fix flashing with roofing cement?
Sealant can be a temporary fix, but it dries and cracks. A lasting repair usually means replacing or properly reinstalling the flashing.
Who should repair roof flashing in Quebec?
A roofing contractor holding the appropriate licence from the Régie du bâtiment du Québec, with proof of insurance.
Spotted a leak around a chimney or skylight? Request a free roofing quote in the Laurentides.

Leave a Reply